Selon versions W 10 le DLNA fonctionne ou pas

[bigbernie]

Bonjour
Je sais que ça n'est pas Mezzmo le responsable mais Windows.
Toutes les explications imagées dans le fichier pdf joint.
Plus rien ne fonctionne.
Merci pour vos idées.

1288

[Peter]

Please try temporarily disabling your Windows Firewall to see if the TV can see the Mezzmo server, if it does then you can try removing all the Mezzmo rules from the Firewall and then go to 'Media Server Settings' and click the button to configure the Windows Firewall. If turning off the firewall does not allow the TV to see the server please try decreasing the server advertisement interval in the Media server Settings dialog from 1800 to 60 to see if the TV can see the server.

[bigbernie]

Thanks a lot
Rien a faire
Desactiver totalement le firewall Defender = ca ne fonctionne pas
Passer l'intervalle de 1800 a 60 ça ne fonctionne pas


Firewall Entrees

4 entrees Mezzmo + 7 entrees Media Server + 15 entrees Media Server Device
Ces 26 entrées ont été supprimées

Configuration du firewall en bas de la page. Configuration Firewall maintenant n'est plus grisée.

Clic. Activation. Mezzmo affiche que le firewall est configuré et OK

Il y a moins d'entrees dans le firewall.
Maintenant
0 entrees Mezzmo
9 entrees Device
2 entrees Media Server.

11 entrees au total et plus 26.
Mode console.
Mais ça ne fonctionne toujours pas.

Selon les versions de Windows ça va fonctionner ou pas sans que je modifie quoi que ce soit dans les configurations.

Windows chez moi empêche TOUS les logiciels DLNA ( j'en ai essaye 6) d'afficher les bibliotheques.
Eh oui.
Pas facile.........

[Peter]

DLNA servers use Notify messages sent as multicast packets over the network to let devices know how to connect to the server, if Windows is not blocking these then a device should receive the Notify and be able to connect to the server. Can you please check the IP address of the device to make sure it is in the same subnet as the PC running the Mezzmo server? Also please check in your router settings to make sure there is not a setting to isolate connected clients from each other enabled.

[bigbernie]

Good morning. Thanks very much
3 differents IP. I'am not able to find the way of doing.
Please read the file pdf added.

[bigbernie]

Dans Mezzmo l'adresse IP, de la TV est donc 0.0.0.0 Ca veut dire qu'il n'y en a pas du tout.
Mais il y a une adresse mac. DO:AE:EC:80:A7:73

Hors avec mon PC il n'y a aucune adresse mac de périphériques qui convienne.

J'ai vérifie sous console avec ipconfig /all
Puis avec la commande CMD getmac
Et avec net view /all
Dans la config de la LiveBox 4 j'ai 13 peripheriques WiFi connectes. En comptant aussi les 2 Liveplugs CPL, mes 2 Firesticks amazon, les 2 smartphones, Amazon Alexa etc
J'ai tout controle un par un.



Mezzmo avec l'IP 0.0.0.0. affiche une adresse mac qui n'existe pas.


I do my best......

[Peter]

The IP address is set to 0.0.0.0 when another device connects to Mezzmo using the same IP address. This happens if the lease on the IP address has expired and the DHCP server in your router has assigned the IP address to another device on the network. If the MAC address of the device is not listed in your PC's cache then there may be a problem for the PC connecting to the device. Have you changed your network configuration since the last time the TV was able to connect to the Mezzmo server by adding a network range extender or another device in the network as this could be masking the MAC address of the TV with it's own MAC address?

[bigbernie]

Thanks
I'ts not easy to manage for an user not expert like you.
22 years using Windows but I'm only an user.
Recently I added a Netgear WiFi Extender but DLNA was out of order since 6 months.
Any DHCP MAC are matching with Mac address in Mezzmo TV config.
DLNA is not absolutely necessary now thanks to FireTV or Chromecast plugs.

DLNA is not necessary for watching medias on PC monitor via Ethernet, usefull only on my TV Smart via WiFi. But do not understandwhat happend exactly and the way to repair I don't like that.
Good night.

[Peter]

The WiFi Extender allows devices to connect to it via WiFi but when a request for the MAC address of one of the devices connected to it is received then the WiFi extender sends back it's own MAC address masking the MAC address of the device connected to it. Mezzmo uses MAC addresses to identify devices uniquely so if all the devices connected to the WiFi extender have the same MAC address they are treated as one device. In 'Media Devices' in Mezzmo there is a checkbox to use only the IP of devices to identify them http://www.mezzmo.com/wiki/doku.php?id=media_devices#use_only_ip_addresses_to _identify_devices_when_turned_on_this_requires_use _of_static_ips_on_your_network which may resolve the issue and allow the TV to see the server.

[bigbernie]

Bonjour
Ca ne fonctionne toujours pas mais j'ai trouve 2 choses en verifiant absolument tout
Ma TV Philips ne reapparait pas dans la liste apres suppression. Malgre reparation par dessus.
Il n'y a aucun Mezzmo dans les Services Windows.

Liste complete des Services. Rechercher Mezzmo....Nothing.]

[Peter]

Did you check the box in Media Devices in Mezzmo to use only IP addresses to identify devices? The WiFi extender may be causing the issue by masking the MAC address of the TV.
There may not be a Mezzmo service running if the Mezzmo server is running as a Windows console process, check in Media Server Settings to see if this is the case.